MDS MDS iNET 900 Manual de usuario

Applies to: MDS manual 05-2806A01MDS iNET 900 TransceiverMANUAL SUPPLEMENTMarch 2004Microwave Data Systems Inc., 175 Science Parkway, Rochester, NY 14

10 MDS iNET ENI Supplement MDS 05-4131A01, Rev. A5. Press A through I (and the up/down arrow keys, if necessary), then enter the desired E-Mail Destin

MDS 05-4131A01, Rev. A MDS iNET ENI Supplement 116. Press A through G to select the baud rate you want the iNET/ENI to use when communicating with the

12 MDS iNET ENI Supplement MDS 05-4131A01, Rev. A7. Press A to enable the iNET/ENI’s COM2 port. See Figure 2-7.Figure 2-7 . Enable COM2 Data Port8. Pr

MDS 05-4131A01, Rev. A MDS iNET ENI Supplement 139. The Wizard asks you to confirm that you want to save the changes. See Figure 2-9. Press Y to save

14 MDS iNET ENI Supplement MDS 05-4131A01, Rev. A2.3 iNET/ENI Error CodesRefer to Table 2-2 for error codes generated by the iNET/ENI.Table 2-2 iNET/E

MDS 05-4131A01, Rev. A MDS iNET ENI Supplement 153. MODBUS to MODBUSTCP SERVER PROTOCOL3.1 IntroductionNOTE: This section assumes you have an understa

16 MDS iNET ENI Supplement MDS 05-4131A01, Rev. A3.2 MODBUS/TCP SERVER CONFIGURATIONPerform the following procedure to configure the MODBUS/TCP SERVER

MDS 05-4131A01, Rev. A MDS iNET ENI Supplement 172. Press A to change the MODBUS serial format, then press the space bar to toggle between the availab

18 MDS iNET ENI Supplement MDS 05-4131A01, Rev. A3. Press A through H to select the desired data baud rate. See Figure 3-4.Figure 3-4 Select Data Baud

MDS 05-4131A01, Rev. A MDS iNET ENI Supplement 195. Press A to enable hardware flow control. Press B to disable hardware flow control. See Figure 3-6.

2 MDS iNET ENI Supplement MDS 05-4131A01, Rev. AFigure 1-1 . Select IP Protocol Screen3. Do one of the following:• If you selected D) DF1/EIP, refer t

20 MDS iNET ENI Supplement MDS 05-4131A01, Rev. A7. Press X to save the COM2 port configuration changes. See Figure 3-8.Figure 3-8 Save COM2 Configura

MDS 05-4131A01, Rev. A MDS iNET ENI Supplement 213.3 EDS FILE INTEGRATIONThe Electronic Data Sheet (EDS) file must be integrated into the Rock-well So

22 MDS iNET ENI Supplement MDS 05-4131A01, Rev. AFigure 3-11 . Graphic Image Screen(Default iNET icon shown)Select “Next” to go to the Final Task Summ

MDS 05-4131A01, Rev. A MDS iNET ENI Supplement 32. DF1 to EIP GATEWAYPROTOCOL2.1 Introduction2The MDS iNET/ENI embeds the EtherNet/IP networking funct

4 MDS iNET ENI Supplement MDS 05-4131A01, Rev. A2.1.2 Related DocumentationThis supplement assumes you have an understanding of EtherNet/IP networking

MDS 05-4131A01, Rev. A MDS iNET ENI Supplement 52.1.3 Differences Between Allen-Bradley ENI and MDS iNET/ENIThe functional differences between the All

6 MDS iNET ENI Supplement MDS 05-4131A01, Rev. A2.2 DF1/EIP PROTOCOL CONFIGURATIONNOTE: The Rockwell application will not identify the iNET/ENI radiop

MDS 05-4131A01, Rev. A MDS iNET ENI Supplement 7Figure 2-2 . Change Security Descriptor Mask3. Press A through I (and the up/down arrow keys, if neces

8 MDS iNET ENI Supplement MDS 05-4131A01, Rev. AFigure 2-3 . Enter Destination IP Addresses

MDS 05-4131A01, Rev. A MDS iNET ENI Supplement 94. Press A to enter the IP address of the optional e-mail server, then press B to enter the E-Mail Fro