MDS MX-2104 Especificaciones Pagina 65
- Pagina / 243
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
MX-2100/2104 Installation and Operation Manual Chapter 1 General Information
Application Considerations 1-49
The KML.8 module uses the HDB-3 line code. Jitter performance complies with
the requirements of ITU-T Rec. G.823. The module has two line interfaces: a
120Ω balanced interface, and a 75Ω unbalanced interface.
ISDN "S" Interface (Module KML.10/S)
The ISDN basic rate access "S" interface complies with ITU-T Rec. I.430. The
interface operates at a nominal rate of 192 kbps, and carries two B data channels
(nominal rate - 64 kbps), one D signaling channel (nominal rate - 16 kbps), and
additional framing and maintenance overhead data. The line coding is 2B1Q. The
line impedance is 100Ω. The user can select whether to connect or not the
internal line termination of the module.
ISDN "U" Interface (Module KML.10/U)
The ISDN basic rate access "U" interface complies with the ANSI T1.601 and ETSI
DTR/TM3002 standards. The line data rate is 160 kbps, and the line coding is
2B1Q. The utilization of the B and D channels is similar to that described above
for the KML.10/S module. The line impedance is 135Ω.
Fiber-Optic Link Interface (Module KML.F)
The fiber-optic link interface of the KML.F module uses a proprietary signaling
format which ensures optimum performance. To optimally meet a wide range of
system requirements, the fiber-optic interface can be ordered for operation over
62.5/125 micron multi-mode fibers (typical attenuation - 3.5 dB/km), as well as over
low-loss 9/125 micron single-mode fibers (typical attenuation - 0.4 dB/km).
Each option can be ordered with ST or FC-PC connectors; SMA connectors are
also available at 850 nm.
Table 1-4 provides information on the characteristics of the optical interface.
Typical range is up to 4.5 km at 850 nm over multimode fiber, up to 45 km at
1300 nm over single-mode fiber with LED transmitters, up to 60 km with 1300 nm
laser transmitters, and up to 100 km with 1550 nm laser transmitters.
Table 1-4. KML.F Fiber-Optic Interface Characteristics
Wavelength Fiber Type Transmitter
Type
Power
Coupled
into Fiber
Receiver
Sensitivity
Optical
Budget
Maximum
Receiver
Input
Power
Receiver
Dynamic
Range
850 nm
62.5/125
µ
m
multi-mode
LED -18 dBm -38 dBm 20 dB -10 dBm 28 dB
1300 nm
9/125
µ
m
LED -18 dBm -40 dBm 22 dB -12 dBm 28 dB
single-mode Laser -12 dBm -40 dBm 28 dB -12 dBm 28 dB
1550 nm
9/125
µ
m
single-mode
Laser -12 dBm -40 dBm 28 dB -12 dBm 28 dB
- MX-2100/2104 1
- MICROWAVE DATA SYSTEMS, INC 3
- FCC-15 User Information 4
- Preface 5
- Conventions 6
- Related Documentation 6
- Quick Start Guide 7
- Contents 9
- Chapter 4 Operation 10
- Chapter 5 Diagnostics 10
- Table of Contents 11
- Table of Contents 12
- List of Figures 13
- List of Tables 14
- Chapter 1 17
- General Information 17
- 1-2 Functional Description 18
- Local MX-2100 Management 20
- Remote MX-2100 Management 20
- Supervision Terminal 21
- 1.2 Physical Description 22
- MX-2100 Rear Panel 23
- MX-2100 Front Panel 24
- MX-2104 Rear Panel 25
- MX-2104 Front Panel 26
- Common Logic Modules 26
- Main Link Modules 26
- Power Supply Modules 27
- I/O Modules 28
- Physical Description 1-13 29
- 1-14 Physical Description 30
- Physical Description 1-15 31
- Basic MX-2100 System 32
- Redundancy (not for MX-2104) 36
- Bypassing Configurations 39
- Location A Location C 41
- Location B 41
- Switch Mode 46
- System Management 48
- In-Band 50
- Out-of-Band 51
- KCL KCL KCL 52
- KCLKCL KCL 52
- System Timing Considerations 54
- A. Leased Line Confi 55
- B. Digital Configuration 55
- Data Channel Clock Modes 61
- Sub Link Timing 63
- 1.4 I/O Module Applications 66
- Chapter 2 71
- Installation 71
- Input Power Requirements 72
- Grounding 72
- Ambient Requirements 73
- 2.3 Equipment Needed 78
- Equipment Needed 2-9 79
- 2-10 Equipment Needed 80
- 2.4 Package Contents 81
- MX-2100 82
- MX-2104 82
- KPS Module 83
- KCL.2 Module 84
- Installing the KCL.2 Module 85
- Table 2-5 90
- Internal MX-2100 Settings 91
- Connections 91
- Initial Configuration 91
- Chapter 3 93
- Configuring MX-2100 93
- Front Panel Menu 94
- Chapter 4, Operation 95
- See Figure 3-2B 96
- See Figure 3-3C 96
- See Module 96
- Manuals in Part II 96
- Only for Data 97
- Channels 97
- Chapter 4 105
- Operation 105
- Command Options 106
- Command Protocol 107
- Index of Commands 108
- See Insert 111
- RTSM-LEAD 112
- E-LEAD DCD 112
- DATAVOICE 112
- 4.4 Operating Instructions 116
- PASSWORD> 118
- KM2100> 118
- KM2104> 118
- TERMINAL ON LINE 118
- Control Session 119
- Ending a Control Session 119
- Front Panel 120
- Normal Indications 121
- Turn Off 122
- Chapter 5 123
- Diagnostics 123
- Special Considerations 124
- Diagnostic Tests 5-3 125
- 5-4 Diagnostic Tests 126
- Diagnostic Tests 5-5 127
- 5-6 Diagnostic Tests 128
- Diagnostic Tests 5-7 129
- Main Link Loops 130
- User or Test 131
- Equipment 131
- 5-10 Diagnostic Tests 132
- I/O Module Loops and Tests 134
- CHANNEL 1 135
- PRBS Transmission 136
- BERT Testing 136
- 5-16 Diagnostic Tests 138
- Appendix A 139
- Connection Data 139
- A.3 MNG Connector 141
- A.4 Alarm Relay Connector 142
- Appendix B 143
- B-2 Alarm Messages 144
- Alarm Messages B-3 145
- B-4 Alarm Messages 146
- Alarm Messages B-5 147
- B-6 Alarm Messages 148
- Alarm Messages B-7 149
- B-8 Alarm Messages 150
- Alarm Messages B-9 151
- Appendix C 159
- SNMP Management 159
- MIB Structure 160
- SNMP Communities 161
- C.3 IP Environment 162
- IP Environment 163
- Automatic IP Traffic Routing 164
- Network B 165
- Network A 165
- Network C 165
- C.4 SNMP Traps 166
- Appendix D 167
- Software Download 167
- Windows-Based Stations 169
- Appendix E 171
- Configuration Parameters 171
- E-2 General 172
- General E-3 173
- E-4 General 174
- General E-5 175
- E-6 General 176
- General E-7 177
- E-8 General 178
- Appendix F 179
- Command Set Description 179
- F.2 Commands 180
- CLR LOOP 181
- CLR MONITOR 182
- CONNECT SWITCH 182
- Purpose 183
- DEF AGENDA 184
- DEF AGENT 185
- F-8 Commands 186
- DEF ALM DEBOUNCE 187
- DEF CALL 187
- DEF CON 190
- Commands F-13 191
- DEF DB FLIP 192
- DEF FRAME 195
- DEF MANAGER LIST 196
- DEF ML CALL 198
- Commands F-21 199
- F-22 Commands 200
- Commands F-23 201
- DEF NAME 202
- DEF NODE 202
- DEF PWD 204
- DEF ROUTE 205
- DEF SYS 207
- Table F-5. System Parameters 208
- DISCONNECT SWITCH 210
- DSP AGENT 211
- DSP ALM 212
- DSP BERT 212
- DSP CH CON 213
- DSP FLIP 214
- DSP HDR TST 215
- DSP MANAGER LIST 215
- DSP KVF5 216
- DSP PBX 216
- DSP KVF6 217
- DSP SIGNALING 218
- DSP SIG 218
- DSP PRBS_INJ 218
- DSP REM AGENT 219
- DSP REV 219
- DSP ST FRAME 220
- Commands F-43 221
- DSP ST ML 222
- Commands F-45 223
- DSP ST SLOT 224
- Commands F-47 225
- DSP ST SYS 226
- Commands F-49 227
- EDIT DB 228
- FLIP ML 229
- INIT DB 230
- LOAD DB 1\2 232
- LOAD IO 232
- ML RECOVERY 234
- MONITOR 234
- REBUILD FRAME 234
- RESET LOC 235
- RESET IO 235
- RESET ML 235
- UPDATE DB 1\2 236
- Downloading Procedure, D-3 241
- Figure 1 243
Relacionado con productos y manuales para Redes MDS MX-2104
Redes MDS Orbit MCR-4G Guia de preparacion
(4 paginas)
(4 paginas)
Redes MDS MX-2100 Manual de usuario
(70 paginas)
(70 paginas)
Redes MDS Orbit MCR-4G Especificaciones
(146 paginas)
(146 paginas)
Redes MDS Orbit MCR-4G Manual de usuario
(4 paginas)
(4 paginas)
Redes MDS TransNET 900 Manual de usuario
(14 paginas)
(14 paginas)
Harbor Freight Tools TORCH KIT 94903 manuals
Owner’s manuals and user’s guides for Tools Harbor Freight Tools TORCH KIT 94903.
We providing 1 pdf manuals Harbor Freight Tools TORCH KIT 94903 for download free by document types: User Manual
Harbor freight tools TORCH KIT 94903 User Manual (8 pages)
Brand: Harbor-freight-tools | Category: Tools | Size: 0.29 MB |
Table of contents
More products and manuals for Tools Harbor Freight Tools
| Models | Document Type |
|---|---|
| 95838 |
User Manual
Harbor Freight Tools 95838 User Manual,
16 pages
|
| 91044 |
User Manual
Harbor Freight Tools 91044 User Manual,
12 pages
|
| 46309 |
User Manual
Harbor Freight Tools 46309 User Manual,
10 pages
|
| 45949 |
User Manual
Harbor Freight Tools 45949 User Manual,
12 pages
|
| DRILL MASTER 97626 |
User Manual
Harbor Freight Tools DRILL MASTER 97626 User Manual,
12 pages
|
| 92453 |
User Manual
Harbor Freight Tools 92453 User Manual,
14 pages
|
| 92703 |
User Manual
Harbor Freight Tools 92703 User Manual,
8 pages
|
| CHICAGO ELECTRIC 38391 |
User Manual
Harbor Freight Tools CHICAGO ELECTRIC 38391 User Manual,
9 pages
|
| 98871 |
User Manual
Harbor Freight Tools 98871 User Manual,
34 pages
|
| Pittsburgh Self-leveling Laser Level 69243 |
User Manual
Harbor Freight Tools Pittsburgh Self-leveling Laser Level 69243 User Manual,
8 pages
|
| 66098 |
User Manual
Harbor Freight Tools 66098 User Manual,
13 pages
|
| CENTRAL PNEUMATIC 46309 |
User Manual
Harbor Freight Tools CENTRAL PNEUMATIC 46309 User Manual,
11 pages
|
| 16 gauge air finish nailer 68023 |
User Manual
Harbor Freight Tools 16 gauge air finish nailer 68023 User Manual,
18 pages
|
| 94837 |
User Manual
Harbor Freight Tools 94837 User Manual,
12 pages
|
| 42528 |
User Manual
Harbor Freight Tools 42528 User Manual,
10 pages
|
| 65161 |
User Manual
Harbor Freight Tools 65161 User Manual,
18 pages
|
| Heavy Duty Air Paint Spray Gun 97855 |
User Manual
Harbor Freight Tools Heavy Duty Air Paint Spray Gun 97855 User Manual,
19 pages
|
| 91062 |
User Manual
Harbor Freight Tools 91062 User Manual,
16 pages
|
| 97719 |
User Manual
Harbor Freight Tools 97719 User Manual,
17 pages
|
| 3-IN-1 Air Framing Nailer 98751 |
User Manual
Harbor Freight Tools 3-IN-1 Air Framing Nailer 98751 User Manual,
18 pages
|
© 2020, manymanuals.es. Todos los derechos reservados | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales